|
Magister's dissertations achieved |
|
|
01 |
Use of direct control of the stator flow and the Kalman filter for direct control of the torque of an asynchronous motor: Application to fault diagnosis |
|
02 |
Optimization of power exchange between an electrical network and other systems |
|
03 |
Diagnosis of the asynchronous machine by finite elements |
|
04 |
Improving the performance of a photovoltaic pumping system over the sun |
|
05 |
Optimal time control of an autonomous vehicle |
|
06 |
Active filtering of harmonics in electrical networks. |
|
07 |
Control of a Parallel three-phase Active Filter by Different Regulators |
|
08 |
Robust torque control of an asynchronous motor with energy optimization |
|
09 |
Optimal vector control of an induction machine powered by a matrix converter - comparative study |
|
10 |
Modeling of sensors in non-destructive testing by eddy current. |
|
11 |
Use of sliding mode observers for direct torque control and vector control of an asynchronous cage machine. |
|
12 |
Sliding Mode Control of an Asynchronous Machine taking into account Faults |
|
13 |
Optimal control of a hybrid photovoltaic generation system. |
|
14 |
Estimated production cost of interconnected electrical networks. |
|
15 |
Transient analysis and position control of an electromagnetic levitation system |
|
16 |
Study and simulation of a HF signal coupler for electrical energy networks, Application: logic selectivity of protections |
|
17 |
Modeling by finit volumes of a non destructive control problem of complex shape |
|
18 |
Contribution to the modeling by the MVF of a current transformer. |
|
19 |
Vector control of an asynchronous machine with fault |
|
20 |
Two-order sliding mode control of the asynchronous machine |
|
21 |
Direct control of the DTC torque of an asynchronous machine with fault |
|
22 |
Detection of stator and rotor faults in the asynchronous machine using FFT and wavelet analysis |
|
23 |
Optimization of the production cost of interconnected networks. |
|
24 |
Simulation of the sliding mode control of a wind chain based on a double-feed asynchronous machine |
|
25 |
Study and characterization of printed antennas for Ultra-Wide-Band systems Etude et caractérisation d'antennes imprimées pour systèmes Ultra- Large-Bande |
|
26 |
Contribution to the study of the active filter Three-level series |
|
27 |
Control of an Active Four-Arm Filter by Advanced Techniques |
|
28 |
Predictive DTC control of an Asynchronous motor |
|
29 |
Microwave characterization methods for printed antennas |
|
30 |
Detection of Static Faults in the Synchronous Permanent Magnet Machine by Advanced Techniques |
|
31 |
Modeling of Asynchronous Machines for Diagnosis, Adequate Consideration of the Magnetic Circuit. |
|
32 |
Sensorless control of a permanent magnet machine |
|
34 |
Vector control of a permanent magnet machine |
|
35 |
Study and modeling of a synchronous generator with permanent magnets driven by a vertical axis wind turbine |
|
36 |
Economic study of a MV line. |
|
37 |
Control of an electrical network. |
|
38 |
Optimal control of the load distribution between the units of a power plant |
|
39 |
Study of a Vertical axis wind turbine at the bottom of a Synchronous Permanent Magnet Machine: Biskra Waste Center Application. |
|
40 |
Study and Simulation of Static Faults of a Synchronous Permanent Magnet Machine |
|
41 |
Ordering a Three-Wire Parallel Active Filter |
|
42 |
Vector control of the permanent magnet synchronous machine |
|
43 |
Determination of the dielectric permittivity from the propagation constant |
|
44 |
Computer-aided design (CAD) of the printed antennas. |
|
45 |
Calculation by the cavity model of the resonant modes of an antenna with rectangular radiating element |